Folger Tech Kossel 2020 3D Printer (Full Kit) Rev B- Assembly required

If you are looking for a fun and exciting 3D printer to build that requires a bit more technical skill than our i3 kit this delta printer might be just what you are looking for. This delta style printer is constructed using 2020 extruded aluminum rails making it strong as well as aesthetically pleasing. This printer also comes with an auto level servo that will set a relative bed level without you making the physical adjustments to the bed. All in all this is a great kit and worth the time required for this slightly more demanding setup.

Rev B: Increased Print Area 210 x 310 mm. 

Benefit of LCD Controller:

2004 LCD Controller w/ SD Card Reader (Print Without a Computer!)

LCD screen with adapter for RAMPS 1.4 controller board. Includes SD card reader, buzzer, stop button, and turnable knob that also acts as a button.

FREE SHIPPING To USA

Lead Time: 6 to 10 Business Days

Folger Kossel Auto Level Delta

** As we receive customer feedback we do make small alterations to the kit if we feel they improve the kits performance and stability, the kit you receive might reflect some of these slight changes and improvements.

 

 

This kit includes the following:

  • Complete Set of Black Printed Plastic Parts Needed.
  • Aluminum corners.
  • Pre-Cut 2020 Aluminum Beam ( x3-700mm x9-300mm).
  • 1x Bearings Set.
  • Nylon Sliders Wheels.
  • Aluminum Heated Bed (3mm x 210mm).
  • x3 End Stop Circuits w/ LED (Incl. 40" Cables).
  • x3 Belt Tension Springs.
  • Carbon Fiber Rods (Need to Be Cut to Length).
  • x12 Tie Rod Ends.
  • Direct Drive Extruder w/ Injection Molded Part (For 1.75mm ABS/PLA) MK9 TYPE.
  • x1 All-Metal Hot End for 1.75mm Filament.
  • All Required Nuts/Bolts for Assembly.
  • 360W 12V 30A Power supply.
  • x4 NEMA 17 Stepper Motors.
  • 5 Meters of GT2 Timing Belt.
  • x3 20 Tooth Pulleys.
  • x1 RAMPS 1.4 Controller.
  • x1 Arduino Mega 2560 R3 Clone.
  • x5 A4988 Stepper Drivers (1 Extra).
  • x1 Roll 8mm Kapton Tape.
  • x1 Inductive Sensor with resistors.
  • Wiring Set.
  • Power Cable.

Features:

  • 210 x 310 mm Print Area.
  • Can print ABS or PLA 1.75mm.
  • Can run 110V or 220V (Only Comes With US cord).
  • Packed And Shipped from the USA.

Items you will need:

  • Tools.
  • Filament.
  • Time.

 

Other items you might be interested in buying with your kit:

2004 LCD Controller w/ SD Card Reader (Print Without a Computer!)

LCD screen with adapter for RAMPS 1.4 controller board. Includes SD card reader, buzzer, stop button, and turnable knob that also acts as a button.

 

prusa i3 LCD display

 

Affordable shipping cost: $0 USD to USA and $60 USD to other countries.

Disclaimer:

This is a kit of components for assembly into a 3D Printer by the end user. Building and using the printer is potentially very dangerous as it involves electricity and high temperatures.

Building the printer will require a certain amount of physical dexterity, common sense and a thorough understanding of what you are doing. We have provided fully comprehensive build documentation to enable you to build your Folger Tech 3D Printer Kit in a safe manner.

However ultimately we cannot be responsible for your health and safety whilst building or operating the printer, with that in mind be sure you are confident with what you are doing prior to commencing with building or buying. Read all of the manual to enable you to make an informed decision.

Building and operating involves electricity, so all necessary precautions should be taken and adhered to, the printer runs on 12V supplied by a certified power supply, so you shouldn't ever have to get involved with anything over 12V but bear in mind there can still be high currents involved and even at 12V they shouldn't be taken lightly.

High temperatures are involved with 3D Printing, the Extrusion nozzle of the hot end runs at 230°C, the heated bed runs a 110°C and the molten plastic extruded will initially be at around 200°C, so special care and attention should be made when handling these parts of the printer during operation.

We wouldn't recommend leaving your printer running un attended, or at least until you are confident to do so. We cannot be held responsible for any loss, damage, threat, hurt or other negligent result from either building or using the printer.

Product Condition
Item Condition New
Manufacturer Warranty 30 days
Printing Specifications
Print size ( X Y Z ) 210 x 310 mm
Print Speed 50 to 100 mm/sec
Layer Resolution 50 microns
Print Precision (Layer Thickness) 0.05 to 0.4 mm
Filament Diameter 1.75mm
Nozzle Diameter 0.4 mm
Filament Compatibility ABS, PLA, Wood, PVA and TPE
Print Plate Size 210 mm (diameter)
Mechanical Specifications
Extruder Type MK9
No.of Extruders One
Print Plate (Build Platform) heated Aluminum bed
Stepper Motors NEMA 17
Software Specifications
3D Printing Software Cura, Repetier Host
Supported File Formats STL
Operating System Windows/MAC/Linux
Temperature Specifications
Extruder Temperature 230°C
Heating Bed Temperature 110°C
Electrical Specifications
AC Input 110/220V AC
Power Requirements 360W
Connectivity (Interface) USB, SD Card (Optional)
Electronics Specifications
Electronics (Motherboard) RAMPS 1.4
Shipping specifications
Machine weight 6 Kg
Shipping box weight 7 Kg
Machine Dimensions 700 x300 mm
Shipping box dimensions 900 x 200 x200 mm
Shipping Location New Hampshire USA
Lead Time (Processing/Handling Time) 6 to 10 Business Days

Write a review

Note: HTML is not translated!
    Bad           Good

Folger Tech Kossel Auto Leveling Delta 3D Printer Kit

Product Code: 3DPO-168
Availability: In Stock
$345 USD $799 USD

Available Options


Tags: delta, folgertech, kossel