Folger Tech Cloner 3D Printer Kit - Assembly required

The Folger Technologies Cloner is a great kit combining the simplicity of an erector set with the power of a much more expensive desktop printer. The kit comes with everything you need to assemble the machine With the use of a few simple tools and a little bit of time you too can get started 3D printing the worlds next big idea.

This kit is a remake of a common open source design that has been improved and made more DIY/Maker friendly using the RAMPS controller with Marlin, and the 2004 LCD with SD card for standalone printing with our the PC.

Benefit of LCD Controller:

2004 LCD Controller w/ SD Card Reader (Print Without a Computer!)

LCD screen with adapter for RAMPS 1.4 controller board. Includes SD card reader, buzzer, stop button, and turnable knob that also acts as a button.

FREE SHIPPING To USA.

Lead Time: 2 to 4 Business days. 

Folger Tech Cloner 3D Printer Kit

** As we receive customer feedback we do make small alterations to the kit if we feel they improve the kits performance and stability, the kit you receive might reflect some of these slight changes and improvements.

Highlighted features:

  • Impressive 230mmx150mmx120mm Build Area.
  • Able to print ABS, PLA, Wood, HIPS, PETG and PVA (1.75mm).
  • Layer Resolution of 50 microns.
  • Print Speed of 60 to 160 mm/sec
  • Supports SD card for offline printing. Print without PC.
  • Oak or Melamine Chassis.
  • Can run 110V or 220V (Only Comes With US Cord).
  • Packed And Shipped from the USA.

This kit includes the following:

  • Complete Set of Black Injections Molded Parts.
  • 2004 LCD with SD card Reader.
  • Laser cut Frame (Melamine or Oak) [Made in the USA].
  • x8 LM8SUU Linear Bearings.
  • x2 SC8LUU Bearings (Bed).
  • x4 MP105 bearings.
  • x1 Idler Pulley.
  • 8mm Chromed Linear Rod for X, Y, Z (Pre-Cut).
  • T8 Lead Screw 2mm pitch.
  • x1 230mmx150mm Bed.
  • x1 Direct Drive Extruder w/ Injection Molded Parts for 1.75mm ABS/PLA/Wood/HIPS/PETG/PVA (Available in Dual or Single Extruders).
  • 360W 12v 30A Power Supply.
  • x4 NEMA 17 2.6kg/cm Stepper Motors.
  • x1 NEMA 17 4.8kg/cm Stepper Motor (Used for Bed).
  • x3 Meters of GT2 Belt.
  • x1 GT2-188 Belt.
  • x6 20 Tooth Pulleys.
  • x1 36 Tooth Pulleys.
  • x1 Ramps 1.4.
  • x1 Arduino Mega 2560 R3 Clone.
  • x5 A4988 Stepper Drivers.
  • x1 Roll of 8mm Kapton Tape.
  • x2 5mmx8mm Couplings.
  • x3 Electronic End Stop Circuits w/ LED.
  • x3 Belt Tensioners.
  • x4 Threaded Bed Adjustment Knobs.
  • x4 Bed Springs.
  • All Required Nuts/Bolts for Assembly.
  • Power Cable.

Items you will need:

  • Tools.
  • Filament.
  • Time.

Build Guide and Firmware/Software:

** Please note the items included inside the below link are often updated to include new and updated information so please bookmark it for your records. Link also contains .stl files to print replacement plastics.

download user manual

Affordable shipping cost: $0 USD to USA and $60 USD to other countries.

Disclaimer:

This is a kit of components for assembly into a 3D Printer by the end user. Building and using the printer is potentially very dangerous as it involves electricity and high temperatures.

Building the printer will require a certain amount of physical dexterity, common sense and a thorough understanding of what you are doing. We have provided fully comprehensive build documentation to enable you to build your Folger Tech 3D Printer Kit in a safe manner.

However ultimately we cannot be responsible for your health and safety whilst building or operating the printer, with that in mind be sure you are confident with what you are doing prior to commencing with building or buying. Read all of the manual to enable you to make an informed decision.

Building and operating involves electricity, so all necessary precautions should be taken and adhered to, the printer runs on 12V supplied by a certified power supply, so you shouldn't ever have to get involved with anything over 12V but bear in mind there can still be high currents involved and even at 12V they shouldn't be taken lightly.

High temperatures are involved with 3D Printing, the Extrusion nozzle of the hot end runs at 230°C, the heated bed runs a 110°C and the molten plastic extruded will initially be at around 200°C, so special care and attention should be made when handling these parts of the printer during operation.

We wouldn't recommend leaving your printer running un attended, or at least until you are confident to do so. We cannot be held responsible for any loss, damage, threat, hurt or other negligent result from either building or using the printer.

Product Condition
Item Condition New
Manufacturer Warranty 30 days
Printing Specifications
Print size ( X Y Z ) 230 x 150 x 120 mm
Print Speed 60 to 160 mm/sec
Layer Resolution 50 microns
Print Precision (Layer Thickness) .05 mm
Filament Diameter 1.75 mm
Nozzle Diameter 0.4 mm
Filament Compatibility ABS, PLA, Wood, HIPS, PETG and PVA
Print in dual color Yes
Mechanical Specifications
Chassis Oak or Melamine
Extruder Type MK9
No.of Extruders Two
Print Plate (Build Platform) HeatBed
Print Head/Hotend/Nozzle Type Brass Nozzle
Stepper Motors NEMA 17
Software Specifications
3D Printing Software Cura, Repetier Host
Supported File Formats STL
Operating System Windows/MAC/Linux
Temperature Specifications
Extruder Temperature 230°C
Heating Bed Temperature 110°C
Electrical Specifications
AC Input 110 / 220 V
Power Requirements 360 W 12 V 30A
Connectivity (Interface) USB, SD Card
Electronics Specifications
Electronics (Motherboard) RAMPS 1.4
Shipping specifications
Machine weight 9 Kg
Shipping box weight 10.5 Kg
Machine Dimensions 457.2 x 457.2 x 406.4 mm
Shipping box dimensions 508 x 508 x 203.2 mm
Shipping Location New Hampshire USA
Lead Time (Processing/Handling Time) 2 Business Days

Write a review

Note: HTML is not translated!
    Bad           Good

Folger Tech Cloner - Dual Extruder 3D Printer Kit

Product Code: 3DPO-244
Availability: Out Of Stock
$360 USD $799 USD

Available Options


Tags: cloner, folgertech, dual extruder